Stuck? support@mecway.com

Mecway

FEA

Recent Discussions

• Where did the solid geometry go?

  315 views 9 comments 0 points Most recent by disla November 2022
• Advice on mesh definition

  170 views 6 comments 0 points Most recent by JohnM November 2022
• Select faces by dimension

  107 views 2 comments 0 points Most recent by Sergio November 2022
• How to set up spring-mass modal vibration model?

  420 views 26 comments 0 points Most recent by Victor November 2022
• Possible to prevent stress calcs in modal analysis?

  222 views 13 comments 0 points Most recent by prop_design October 2022
• Torsion constant of Rectangular Tube

  215 views 4 comments 0 points Most recent by cwharpe October 2022
• x6 difference in displacement between internal solver and CCX (beams+shells)?

  317 views 17 comments 0 points Most recent by prop_design October 2022
• Version 17.0

  468 views 4 comments 0 points Most recent by Victor October 2022
• Improvement Suggestions for Mecway

  138 views 1 comment 0 points Most recent by Victor October 2022
• Line2 - Beam - parameters needed for stress calculations

  127 views 4 comments 0 points Most recent by JMF11 October 2022
• Contour plot -- Greyscale gradient seems wrong

  146 views 6 comments 0 points Most recent by disla October 2022
• Moment load applied on shell

  96 views 2 comments 0 points Most recent by Victor October 2022
• Radial stiffness of PreCalibrated Bushings ( Wöhler - Curve; W-N curve )

  480 views 17 comments 0 points Most recent by disla October 2022
• MYSTRAN/NASTRAN Support

  205 views 0 comments 0 points Started by FEA_Stress October 2022
• Assigned custom colors for contour plot are not correctly displayed

  260 views 14 comments 0 points Most recent by dculp October 2022
• Beam elements using CCX solver

  336 views 4 comments 0 points Most recent by Victor October 2022
• 3D meshing -- How is "Maximum element size" determined?

  729 views 7 comments 0 points Most recent by disla October 2022
• Error: Problem opening temporary files

  102 views 3 comments 0 points Most recent by Victor October 2022
• free version - cant save a 900 nodes model

  134 views 3 comments 0 points Most recent by Victor September 2022
• Maximum principal plastic strain

  313 views 3 comments 0 points Most recent by Victor September 2022
• gmsh from Mecway's GUI - any way to specify minimum number elements per edge?

  176 views 3 comments 0 points Most recent by afro_samurai September 2022
• Two concentrated loads/fluxes different amplitudes.

  134 views 4 comments 0 points Most recent by disla September 2022
• *SURFACE BEHAVIOR,PRESSURE-OVERCLOSURE=TIED

  283 views 6 comments 0 points Most recent by disla September 2022
• What are the right settings for environment variables for CCX (Mecway 16.0)

  265 views 1 comment 0 points Most recent by Victor September 2022
• Forum Search Refinement

  103 views 2 comments 0 points Most recent by cwharpe September 2022
• Maximum and minimum numerical values. Round-off .

  113 views 2 comments 0 points Most recent by disla September 2022
• Extra parameters for integral solutions

  567 views 16 comments 0 points Most recent by DRQ September 2022
• Loads and boundary graphics not visible in results when using CCX solver?

  103 views 3 comments 0 points Most recent by afro_samurai September 2022
• Sanity check on a steel structure.

  642 views 17 comments 0 points Most recent by LHartley September 2022
• Can't Project to Target MESH

  98 views 3 comments 0 points Most recent by Victor August 2022